< td>U.C.R.L Color Codes/ For Identification And Safety < td>Sencondary Emmision Of Various Metals < td>

Berkeley Design Data

Doc #
Title
Author
Date
1
Presure Deflection Curves For Rubber Gaskets
E,D,Kane
5/20/1946
2
Heat Transfer At Moderate Temperatures
W.M. Brobeck
5/30/1946
5
Presure Drop In Forevacuum Pipes For Streamline Flow
W.M. Brobeck
9/10/1944
6a
Properties Of Slected Ceramic Materials
R. Reimers
1/3/1968
10
Water Flow In Small Small Tubes, Such As Brass And Copper
R.Peters
1/17/1947
11
Properties And Indentification Of Mica
W.W. Salsing, Jr.
2/24/1947
12
Rules For Making Graphs
W.M. Brobeck
3/14/1947
13
Power Required To Rotate A Hollow Sharft In A Magnetic Field
E.M. McMillan per W.M.B.
3/14/1947
15
Radio Frequency Power Loss In Sheet Conductors
W.M. Brobeck
3/17/1947
16
Vibration Isolation
Marvin Martin
6/20/1947
17
Pumping Speed Of Pipes & Orifices At High Vacuum
Marvin Martin
4/2/1947
18a
Tensile Properties At Room Temperature Of Frequently-used unwelded And Welded Aluminum Alloy Sheet And Plate
John E. Cullen
12/1/1967
19b
W.Carpender/ E. Steele
6/17/1952
22
Factors For Calculator Thead Dimension By Three Wire Mthod - 60 American National Form
W.M. Brobeck
9/4/1947
23b
Chevron Seals Internal Parts
J. Dols
7/21/1970
24
Heat Transfer Between Contact Surfaces In VAcumm
W.M. Brobeck
11/3/1947
25a
Braze Filler Metals And Brazing Practice (Hard Solders, Silver Solders)
Ralph Peters
8/14/1964
27a
Recommended Standard Bolt Hole Layouts For Lightweight Flances
W.M. Brobeck
10/28/1948
28
Generaal Motors Standars Recommended Practices For The Spot Welding Of Mild Steel
Automotiye Industfies Publication
12/14/1948
29
Convenient Factors For Use In Cooling Calculations
W.M. Brobeck
2/8/1949
30
K.W. Perton VS. Temperatures of Electrical Conductors
4/29/1949
32
Formulas For Particle Accelerator Calculartions Using "Electron Volt" Units
W.M. Brobeck
8/15/1949
33
Properties Of Non-Magnets Manganese Steels
W.C. Twichell
11/2/1949
35
Conversion Chart For U.C.R.L Preferred Heat Transfer Units
H.Gordon, et al
11/12/1949
36
Friction Factors For Pipe Flow
L.E. Brown
4/27/1951
37
Properties Of Metals At Low Temperatures
R.A. Nickerson
7/11/1950
39
Calculation Of Ultimate Pressure Of Kinetic Vaccum Systems Using Rubber Gaskets And Others Volatile Materials
Marvin Martin
11/1/1950
40a
Pipe, Conduit, And Tubing Benders Available In Berkeley LRL Shops
D. Vorkoeper
12/21/1950
43
Brass Specificat ions
B. Nickerson
4/17/1951
44
Magnetic Perneability Of Could Worked 18-8 Stainles Steels
Nickerson, R.
5/28/1951
45
Electron Work Functions Of The Elements
H.P. Hernandes
8/17/1951
46
Vapor Presure vs. Temperature
V. Mc Claim
9/12/1951
47a
Surface Finishes, Typical Applications And Relative Costs
Ralph Frey
10/11/1951
48a
Threads - Loads And Stresses Per Unit Torque
Lee R. Glassgow
1/23/1973
51
Stud Spacing For Gasketed Flanges
R. Meuser
3/27/1952
52
Coling Tube Spacing vs. Maxium Teperature Difference On Uniformly Heated 16 Gage (.065) Coper Sheet
D. Vance
2/27/1952
53
References To UCRL Design Information (Other Design Data)
D. T. Scalise
4/9/1952
54
Characteristics Of Pure Tungsten Filaments
T. W. Macomber
10/14/1944
55a
Mechanical Vaccum Pumps
Gerald Pfaff
7/9/1964
56c
Magnet Design Information
A. Schmidt,et al
7/10/1964
57
Calculation Guide For Internally Cooled Magnet Coils
L.E. Brown
7/11/1964
58a
Copper Conductors For Magnents Recommended Standard Sizes, Prices, And UCRL Stock
H. Gordon,et al
7/12/1964
59
Liquid Nitrogen Consumption Of Traps
R.B. Meuser
7/13/1964
60
Approximate Focal Length O f Wedgets With Uniform Magnetic Field
W.M. Brobeck
7/14/1964
61
Rockwell Hardness Scales Compared With Brinnel Hardness Numbers WD With The Brinnel Hardness Ranges Of Some Common Metals
M. Paul Hernandes
7/15/1964
63
Heat Conductivity Of Metals And Allots
R.A. Nickerson
7/16/1964
64a
Tap Drill Depths
W.M. Brobeck
7/17/1964
65e
Table II: O Rings Standard Series
66
Properties Of Materials Aproximate Electrical Resistivities Of Metals And Alloys
L. Polentz
2/17/1953
67
Heat Transfer By Radiation For Small Body In A Large Enclosure.
L. Polentz
2/28/1953
68
Recommended Filler Metals For Joining Similar And Dissimilar Metals
1/19/1951
71a
Precious Braze Filter Metals
Richard Reimers
8/28/1964
72
Allowable Bending Moments Of Commonly Used Section
C. Perkins
6/19/1984
73
Spacing For Bare l.P.S (Iron Pipe Size) Pipe With Flances
Keller & Gannon W E Sarrus
10/5/1955
74
"Hipe rco" And "Permendur" High Cobalt, High Magnetic Saturation Alloys, Properties, Fabrication, Estimating Costs
J. O. Turner
10/9//59
75
Beam Calculations Specials Case Of Symmetrical Overhanging Beams With Uniform Load w lbs/ ft
D. Vorkoeper
10/4/1960
77
D. C. Magnet Coils Temperature Rise Time Of Non-Cooled Copper Conductor
H. Paul Hernandez
2/19/1962
78
Lawrence Radiation Laboratory University Of California, Be rkeley
W.H. Chamberlain
3/5/1964
79
Break Down Voltage vs. Gap For The Most Important High Voltage Electrode Materials II - Without Magnetic Field
Bob H. Smith
5/1/1964
80
Break Down Voltage vs. Gap For The Most Important High Voltage Electrode Materials I - Without Strong Magnetic Field
Bob H. Smith
5/1/1964
81
Universal Field Emission Chart UA = Work Fuction Of Surface Material
Bob H. Smith< /div>
5/1/1964
82
Thermionic Emission As A Function Of Temperature And Work Function
Bob H. Smith
5/1/1964
83
Thermionic Emission For Most Usual High Temper ature Materials
Bob H. Smith
5/1/1964
84
Material Constants Which Determine Electron Emission
Bob H. Smith
5/1/1964
85
Bob H. Smith
5/1/1964
86
Thermal Radiation-Temperature vs. Heating Density
Bob H. Smith
5/1/1964
87
Thermal Conductivity vs. Temperature For The Most Important High Temperature Materials
Bob H. Smith
5/1/1964
88
The Satutation Vapor Pressure As Function of Temperature For The Most Important Elements Of High Vacuum Technique
Bob H. Smith
5/1/1964
89
Mean Free Path Of Molecules Of Several Gases As A Fuction Of Pressure
Bob H. Smith
5/1/1964
90
Stand Wire Rope Sling Single Leg With End Loops Standard Cr ane Lifting Equipment
I. Halpern
12/8/1964
91
Realative Dielectric Strenghths Of Various Gases And Nitrogen-Vapor Mixture
Bob H. Smith
3/16/1967
92
Exicitation And Ionization Potentials
Bob H. Smith
4/24/1967
93
LRL Standard Stainless High Vacuum Flanges, Dimension And Applications
Richard Reimers
4/26/1967
94
Bending Magnet Pole Tip Minimum Width
P. Hernandez
11/20/1967
95
Graphic Symbols To Be Used In Vacuum Technology
Dick Reimers
10/2/1968
96
Thick-Walled Cylindrical Pressure Vessels Nomogram For Lame's Equation
J. O. Turner
10/3/1968
97a
Moment Formulas For Rigid-Corner Rectangular Frames
J. O. Turner
10/3/1968
98b
LRL Standard Tubing Fittings Outline Dimensions And Typical Applications
J. J. Dols
12/6/1971
99
Vacuum Vessel Design
F. S. Reinath
7/8/1970
100
Elliptical Chamber Stresses And Deflections Under Uniform Presure Loading
R. T. Avery
7/7/1970
101
Distortion Of Square Hollow Copper Conductor At Bendes
J. Gunn
5/4/1973